Are you still using the fishing box? Anyway, I have long been needed because I feel too heavy. Recently, I have seen many works sent by big guys in my heart. So I ’m integrated with the research results of the big guys and my own sudden imagination. Essence
Let’s talk about the advantages of fishing barrels first
1. Light and flexible; compared to the fishing box and fishing barrels, it can reduce the load. It is not a long way to carry a dozen pounds of fishing.
2. The material is sufficient; there are several decoration left -off waste plastic buckets in any house, and you don’t need to save a lot of expenses for a penny.
3. Storage artifacts; this depends on how to use it to catch the fish according to your own habits and put it in the barrel and put it with water to add oxygen. Most of the fishing gear can also be placed in the barrel. The advantage is that buying fish with suitable size will be placed in the barrel after fishing, and there will be no odor without leakage. It is really a convenient and practical multifunctional barrel.
4. Powerful functions; you can convert it into what you want according to your own habits, bait racks, fish racks, rod racks, water cup holders, and lamp racks.
5. Add fun; everyone is pursuing the principle of fishing instead of fish. The two groups of three groups are playing. Whenever a friend has a new fishing artifact, then it will become the point of attention by the river. I have made a lot of new friends who love fishing. It is really endless.
The disadvantage of fishing barrels is that the bottom of the barrel is flat, but how can we find so many flat land when we fish, we still need to raise their home improvement. The general fishing box lift foot is embedded in one, and the ordinary barrel is not easy to install. One is to screw in with wooden screws or tighten with a screw nut, but one thing is to destroy a few holes on the barrel body. If water is installed, it will feel like leaking. In order to enhance the support of the barrel, I can usually add two tin buckets to the bucket when installing parts for barrels. It is much stronger. In order to prevent the barrel leakage, some great gods are used. The intensity of enhancement is also guaranteed to be worth learning!
After watching the masterpieces of the great gods, they are also studying. They are simple and practical and do not destroy the barrel body. Although they have just done part of them, they can’t help but want to share with you.
This is the lifting of the bracket I made, which saves the lock welding. The method of connecting the two grades is used to form a ladder -shaped by using the thread link, because the barrel itself is cone -shaped. The brackets made are tried to use most plastic buckets.
Please look at the picture above. The size above is slightly smaller than the size below. When holding the bracket tightly on the barrel with a hug, it is perpendicular to the ground when it is installed. Even by force.
Open the holes with a slightly greater tank and width on the hug thickness and width on the slot so that can be firmly tightened on the barrel wall. The grooves close to the barrel wall should make the arc that is similar to the barrel on the bottom of the barrel and the upper part of about 260 mm and the diameter of the diameter and the upper part. Of course, 270 mm is also different.
The upper arc is slightly larger, and the bottom is slightly smaller, which can ensure that the upper and lower arcs are closely pasted to the barrel body, which enhances the support of the barrel. After hugging, it can support the weight of an adult and parts.
The lower part of the bracket is to install the lifting foot. The lower side of the steel lifting foot is aligned with the bottom edge of the bracket, and then use the pen to make a hole in the four holes. The wooden screws should be drill with a diameter slightly less than the diameter of the wooden screw, and the bolts use the same diameter drill.
In order to install it for convenience, it is better to use electricity batch. The anti -retreat 304 hexagonal screws are not long -rust.
The two grooves are used to overlap the thread. All the two grooves are threaded. There are four contacts on each bracket to minimize the gap between the two grooves, which makes the intensity higher and the production is quite difficult. This … what’s the matter. Favorite friends click like (个 ▽ ≦)/